Device driver is instructed to transfer disk data to a buffer address X. 2: Device driver then instruct disk controller to transfer data to buffer. 3: Disk controller starts DMA transfer. 4: Disk controller sends each byte to DMA controller. 5: DMA controller transfers bytes to buffer, increases the memory address, decreases the counter C until. Windows 7 & Vista: Right-click on the hardware's name or icon, choose Properties, then the Driver tab, followed by the Update Drive button. The Update Drivers or Update Driver Software wizard will begin, which we'll completely step through to finish the driver update for this piece of hardware. . A Windows setup disk. Motherboard driver disk. A USB thumb drive. 1 Configuring SATA Controllers A. Installing hard drives Connect the SATA signal cables to SATA hard drives and the Intel® Chipset controlled SATA ports (SATA3 05) on the motherboard. Then connect the power connectors from your power supply to the hard drives. I tried different driver versions (both the 5.80 and 6.10 and also newest driver supplied with Windows 10 x64) and the situation is the same: while both Hard Disk Sentinel (and the VIA RAID tool) can identify all hard disks and show their details (model, firmware version, serial number, features, etc.) the self-monitoring status is missing for. Note that all hard disk controllers provide hard disk status information in single/standalone mode only unless RAID mode is listed for the appropriate hard disk controller (RAID controller). Note: the firmware update for ASMedia ASM1051 USB3.0 bridge may work with enclosures, adapters based on this chip to get the missing status information.

Via Hard Disk Controller Driver Windows 7
Via Hard Disk Controller Driver In Das Architecture Is Replaced In San Either With
Via Hard Disk Controller Driver Updater
VIA Hard Disk Controller Driver

Errors: No Drives Were Found. Click Load Driver to Provide a Mass Storage Driver for Installation

During the process of installing Windows OS on a specified HDD or SSD, you may surprisingly find that the hard disk is not detected during the Windows installation, with either of the following error messages coming along.

'We couldn't find any drives. To get a storage driver, click Load driver.' 'No drives were found. Click Load Driver to provide a mass storage driver for installation.'

However, clicking 'Load Driver' doesn't solve the problem at all. What's the next move then? Have you found viable solutions to troubleshoot hard disk not detected in Windows 10 or Windows 7 installation even it's normally connected to the computer?

Workable Solutions	Step-by-step Troubleshooting
6 Solutions to Fix Hard Drive Not Detected	Method 1. Use a Different SATA Port...Full steps Method 2. Load RAID Driver for RAID Disk...Full steps Method 3. Check the Hard Drive in BIOS...Full steps More ways...
Bonus Tip: Free Partition Manager to Enhance System Performance	Launch EaseUS Partition Master on your PC > Free up space...Full steps

How to Fix Hard Disk Not Detected in Windows 10 Installation

Even though Windows 10 or Windows 7 installations include almost all disk drivers, the 'No drives were found. Click load driver to provide a mass storage driver for installation' issue occurs from time to time and you find no way to out. When you encounter Windows 10 install not detecting hard drive or Windows 7 couldn’t find any drivers to get storage driver problems, try the practical six ways below.

Method 1. Use a Different SATA Port

If you are using a desktop computer, try using a different SATA port and see if that helps at all. Sometimes they come with two different controllers.

Method 2. Load RAID Driver for RAID Disk

Windows 10 install not detecting hard drive mostly occurs on RAID disk. In this case, you need to load RAID drivers manually to fix the issue.

Step 1. On the Windows Setup windows, you will see Where do you want to install Windows? And there is no hard drive detected. Click 'Load Drivers' at the bottom left of the screen, then click 'Browse' to choose the device driver.

Step 2. Go to your computer or storage device to find and load an available RAID driver.

Step 3. After the device diver has been loaded, Windows 10 installing will successfully detect the hard disk. Then, follow the onscreen instructions to install Windows.

Method 3. Check the Hard Drive in BIOS

Otherwise, take some time to check if hard drive shows up in BIOS, especially you're installing an operating system from a bootable USB or CD/DVD disc.

By holding and pressing F2, you'll enter BIOS settings. See if the hard drive showing up there. Click solution to repair hard drive not showing in BIOS.

If not, check your BIOS settings for the following parameters:
* SATA configuration -> Enhanced
* Configure SATA -> AHCI

Method 4. Check the Status of Your Hard Drive

Step 1. Press Windows + R and the window will pop up.

Step 2. Input devmgmt.msc and press Enter.

Step 3. Choose Disk Drives and right-click the hard drive.

Step 4. Click Properties and check the status of your hard drive. If it is Ok, showing 'This device is working properly'.

Method 5. Boot from Windows 10 Install Media

Microsoft also provides a method about boot from the Window 10 Install Media. You can take these steps to fix the issues 'drive not showing up when Windows 10 install'.

Step 1. Choose Install Now > Accept License Agreement > Choose the installation type and click 'Custom Advanced'.

Step 2. Press Shift + F10.

Input each command and press Enter: DISKPART > list volume > select disk* > clean > convert mbr > create partition primary > active > format quick fs=ntfs >exit

Then you can install Windows again.

Method 6. Ask Help from the Manufacturer

Since the manner of installing or reinstalling Windows OS happens so frequently that most personal PC or desktop manufacturers have built-in checking tools for quick troubleshooting and repair. For example, Dell Online Diagnostic Tool, Lenovo Diagnostic Software for Hard Drive Quick Test, etc. So if you're their customers, feel no hesitate to ask help from the manufacturer and learn how to use tools to fix hard drive not detected issues alright.

Bonus Tip: Free Partition Master to Enhance System Performance

You can enjoy the exciting features of the latest system after successful Windows 10 installing. Furthermore, to enhance system performance and let software and hardware cooperate to achieve an optimal operating state, it’s necessary for you to have free partition management software, which enables you to organize and optimize your hard drive to extend your computer's life and capableness.

EaseUS Partition Master Free is a versatile partition management program that provides one-stop partition and disk management solutions, for instances:

Resize/move partitions by sliding the partition left and right or enter the exact partition size you want, such as increase C drive to speed up your computer (move space from D drive to C drive supported by paid version)
Create, format, delete, copy, and merge partitions
Clone an entire disk to another even the destination partition is smaller than the source
Convert file system from FAT32 to NTFS, convert MBR to GPT, convert dynamic disk to basic disk and vice versa, and so on
Completely wipe out all the data on hard disk permanently

Now, download this ultimate Windows 10/8/7 disk management tool and follow the simple steps below to resize and move your partitions.

Step 1. Launch EaseUS Partition Master on

VIA Hard Disk Controller Driver